oki e lectronic components f ed foat1042x - v1 - 01 issue data : feb . 4, 2002 oat1042x - v1 - z - yy oc192/stm - 64 optical transceiver module 1 / 5 a pplication oc - 192 and stm - 64 serdes transceiver module features transmission distance 12km wavelength 1310nm 1:16 demux with lvds differential 622mbps data outputs 16:1 mux with lvds differential 622mbps data inputs tx/rx loss of lock com pact size supply voltage; +3.3v , +5v and - 5.2v specification optical interface specifications parts number oat1042x - v1 - z - yy parameter for 12km units transmitter module pout - 4 to 0 dbm l c 1290 to 1330 nm op tical output waveform itu - t g.691 stm - 64 unamplified mask standard extinction ratio 8.2 db dl 20 1.0 nm smsr 30 db jitter generation compliant with gr - 253 receiver module minimum sensitivity - 12 dbm minimum overload 0 dbm l c_rx 1290 ~ 1600 nm rx return loss 27 db jitter gener ation, tolerance and transfer compliant with gr - 253 optical path d lrmax 40 ps/nm system optical return loss 24 db optical path penalty 1 db
f edf oat1042x - v1 - 01 oki semiconductor oat 1042x - v1 - z - yy 2 / 5 power supply parameter symbol min. typ. max. units imax supply voltage vdd 3.1 3 3.3 3.4 7 v 2a vcc 4.75 5 5.25 v 0.8 a vee - 4.9 4 - 5.2 - 5.45 v 1.8a power consumption 8 14 w operating temperature(case temperature) 0 to 65 degc dimensions (without heat sink) dimensions units width 88.9 length 114.3 height 13 mm connector optical select sc / fc / lc / mu electrical 300pin berg megarray@84502 - 10x
f edf oat1042x - v1 - 01 oki semiconductor oat 1042x - v1 - z - yy 3 / 5 block diagram lstempmon lsbiasmon lspowmon lsenable txdin0-15p/n txpiclkp/n oc192 optical output txlockerr tx e-o driver power control lsbiasalm lstempalm temp control txrefclkp/n txlinetimsel rxpoclkp/n rxdout0-15p/n rxrefclkp/n rxlockerr oc192 optical input rxpowmon i2cdata i2cclock rx o-e cdr with demux post amp up eeprom optional function source and line timing modes txpclkp/n mux with cmu txreset txrefsel optional function manufacturing infomation stored txmclkp/n rxlckref alm rxpowalm rxreset rxmclkp/n ordering informatio n oat1042 x - v1 - z - yy x z yy optical connector bitrate(gbps) fiber length s sc a 9.95 10 1m f fc b 10.3 05 0.5m l lc c 9.95/10.3/10.7 m mu d 10.7
f edf oat1042x - v1 - 01 oki semiconductor oat 1042x - v1 - z - yy 4 / 5 package outline (unit : mm) opt in opt out
f edf oat1042x - v1 - 01 oki semiconductor oat 1042x - v1 - z - yy 5 / 5 notice 1. the information contained herein can change w ithout notice owing to product and/or technical improvements. before using the product, please make sure that the information being referred to is up - to - date. 2. the outline of action and examples for application circuits described herein have been chosen as an explanation for the standard action and performance of the product. when planning to use the product, please ensure that the external conditions are reflected in the actual circuit, assembly, and program designs. 3. when designing your product, ple ase use our product below the specified maximum ratings and within the specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating temperature. 4. oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond t he specified maximum ratings or operation outside the specified operating range. 5. neither indemnity against nor license of a third party?s industrial and intellectual property right, etc. is granted by us in connection with the use of the product and/or the information and drawings contained herein. no responsibility is assumed by us for any infringement of a third party?s right which may result from the use thereof. 6. the products listed in this document are intended for use in general electronics equ ipment for commercial applications (e.g., office automation, communication equipment, measurement equipment, consumer electronics, etc.). these products are not authorized for use in any system or application that requires special or enhanced quality and r eliability characteristics nor in any system or application where the failure of such system or application may result in the loss or damage of property, or death or injury to humans. such applications include, but are not limited to, traffic and automoti ve equipment, safety devices, aerospace equipment, nuclear power control, medical equipment, and life - support systems. 7. certain products in this document may need government approval before they can be exported to particular countries. the purchaser ass umes the responsibility of determining the legality of export of these products and will take appropriate and necessary steps at their own expense for these. 8. no part of the contents contained herein may be reprinted or reproduced without our prior perm ission. 9. qualification and reliability to help ensure high product reliability and customer satisfaction, oki is committed to an intensive quality program that starts in the design phase and proceeds through the manufacturing process. optical trans ceiver modules are qualified to oki internal standards using mil - std - 883 test methods and procedures and using sample techniques consistent with telcordia requirements. this qualification program fully meets the intent of telcordia reliability practices gr - 468 - core. 10. laser safety all version of transceiver are class 1 laser products fda complies with 21 cfr 1040.10 and 1040.11 requirements. also, all versions are class 1 laser products pre iec 825 - 1 . copyright 2002 oki electric industry co., ltd.
|
